Buying Used Inflatable Boats
There are plenty of online stores that sell inflatable boats nowadays. You have a wide array of choices that sometimes choosing the best one for you is quite a task. In some cases,it is better to source for a used inflatable boat.
How do you choose a used boat? Here is a checklist of the things that you need to inspect when buying a used boat:overall appearance;fabric condition;tube seams;hard-bottom-to-tube seams;bottom seams;transom-to-tube seams;outboard bracket;bottom abrasion inside and outside;valve condition and operation;valve-to-tube seams;oarlocks;floorboards;transom;steering cables;oars and paddles;pump;owner’s manual and repair kit.
The list is extensive as it’s the same checklist for a new inflatable boat. Make sure that the boat is inflated without the engine,floorboard and other things. Check the fabric of the boat. It is alright for a Hypalon to have a chalky fabric but not on a PVC boat. Check that the boat is not coated with petroleum jelly or oil to make it look good. PVC boat is especially vulnerable to silicone-based protectant such as Armourall.
It is not easy to tell from its looks if a boat is made of PVC or Hypalon. Most manufacturers call their Hyaplon boats “Hypalon”but when PVC is used manufacturers tend to hide them behind some obscure name. A seller might not actually know if Hypalon or PVC is used in his boat as it might have been sold under the name Strongan or Decitex or Sevylor. To check,get acetone or nail polish remover and place a spot on the boat. If the wet area becomes sticky after a few seconds,then the material is PVC. If it is not affected,then it’s Hypalon. It is best to test the tube fabric too as some manufacturers make tube fabrics different from the floor and dodgers. It is also almost a certainty that the sport boast is made of PVC when the transom is attached to the hull flange using bolts or screws.
Make sure you check the seams for leaks. You can do this by using water and dishwashing liquid on the seams. If there are bubbles,then there are leaks. Small leaks are fine especially if the boat is a bargain –generally good condition at a very reasonable price.
Check the seams that attach the bottom fabric or fiberglass hull to the tubes. Make sure there are no exaggerated abrasions on the interior and exterior. Check that the transom is not in any danger of separating from the tubes which is especially true in PVC boats.
Air-tight inflation valves should be present in each air chamber. Make sure that the diaphragms inside the valves are intact as these are the check valves that keep the air in the boat. If the boat is old model,you might find it difficult to find replacement diaphragm.
Check that the general condition of the wood- transom,floorboard and oars is sound. Blistered paint or varnish is fine as long as the wood has not deteriorated. Since marine plywood is generally used,you should not have a problem in this area. Check that the oarlocks are in position and not missing.
Check that there’s a good manual inflation pump included in the boat. Make sure that the nipple fits for ease in inflating and deflating. Do not forget the windshield,lifelines,dodger,seats and other mechanical equipment. Make sure the owner’s manual and repair kit is intact.
Get a second opinion. If you are buying a small boat that does not cost a lot of money,then it is alright to trust your own judgment and buy or junk the boat. However,if you are about to buy a big RIB that costs thousands of dollars,it would be to your advantage to have it looked over by a qualified boat repair person or an authorized service center. A boat survey will give you an unbiased list of the things that you need to do in order to bring the inflatable back to prime condition.
Will the expenses be worth it or will it be better to buy a new one? The decision is yours.
For more information about buying used inflatable boats please visit:
http://inflatable-boats-kayaks-and-canoes.com/buying-a-used-inflatable-boat/default.php
About the Author
Makita 9227CX3 7-Inch Hook and Loop Electronic Polisher-Sander with Polishing Kit $408.00 Makita’s 7-Inch Electronic Polisher-Sander with Polishing Kit is a favorite among automotive and marine enthusiasts for polishing and sanding. The 9227CX3 combines 10 AMP power and variable speed control with a pre-set maximum speed dial. The result is fast and powerful polishing for clearcoat finishes,and more. It can also be easily converted to a sander..c26-caption{font-family:Verdana,Helve… |
Black &Decker WP107B 7 Sander / Polisher $62.62 Includes 7-in Sander-Polisher –WP107B,Wool Bonnet… |
DEWALT DC515K 1/2 Gallon 18-Volt NiCd Cordless Wet/Dry Vac $114.99 The DeWalt DC515K Heavy Duty 1/2-gallon 18-volt Ni-Cad Cordless Wet/Dry Vacuum features dual clean-up modes for debris clean-up with either the front utility nozzle or the extendable heavy-duty rubber hose. The vacuum’s 1/2-gallon tank with heavy-duty latch is easy to empty and clean,and an included Gore HEPA wet/dry filter traps 99.97-percent of dust at 0.3 microns. The filter is washable with t… |
Wilson Electronics Cell Phone Signal Booster Kit for Vehicle with Low Profile Antenna –For Multiple Users $429.95 Increase your cell phone’s signal by up to 25 times with the Wilson Cell Phone Signal Booster Kit. Designed for use in your car,truck,RV,or boat,the booster kit significantly improves your cell phone’s performance and signal strength. You’ll experience fewer dropped calls,faster data rates,and clearer reception. Also,the booster is powerful enough to improve the cellular signal on multiple … |
Midland NTVP1 Nautico 88-Channel Water-Resistant VHF Marine Two-Way Radio $43.79 Stay in touch with your friends and family and be covered in emergencies with Midland’s Nautico 1 Marine Radio Kit. The Nautico 1 boasts five watts of power for a range of up to 12 miles,with access to all US and international marine channels,and NOAA weather alert radio. It features a water-resistant body,a brilliant LCD,and convenient features like eVox,auto squelch,an emergency channel … |
Peerless PA730 Articulating Wall Mount for 10 to 22 Displays (Black) $119.99 The Peerless PA730 Articulating Wall Arm for 10-22 In. LCD Screens makes it easy to get the best viewing position and comes in high gloss black. You can effortlessly pull out the screen from the wall,position it in almost any direction,even turn it around corners and then smoothly return it to the wall when finished. Level the screen at any time,even after installation,for that picture perfect… |
Nickel Silver Rivetable 7/8 Pinback $4.99 Rivet-able 7/8″Pinback… |
Intex Motor Mount Kit $20.30 Intex Motor Mount Kit lets you attach up to a 3.5-horsepower motor to the rear of your Intex boat,so you can rest your paddling arms and float in comfort. The mount–which is made of marine plywood with aluminum support arms–attaches and detaches easily,so you don’t have to spend a half hour fussing with the components each time you want to use the motor. Plus,the mount disassembles quickly wh… |
Darice Wood Model Kit-Titanic $0.53 Wood Model Kit. These fabulous little wood kits are great for school camp,scout activities and at home. Each kit contains precut wood easy to follow instructions for assembly and finishing all you need is the glue,sandpaper and paint (sold separately)! There is a variety of kits available from cars to jets,bird houses to bird feeders and many more,each sold separately. Size,shape and number o… |
Titanic 14 Model Cruiseship –Already Built Not a Kit –Wooden Ship Model Cruise Ship Replica Scale Model Boat Nautical Home Beach Wall Décor or Gift –Sold Fully Assembled $39.99 SOLD FULLY ASSEMBLEDReady for Immediate Display –Not a Model Ship kitThis adorable model cruise ship is inspired by history’s most famous ocean liner,the RMS Titanic.Ideally sized to rest upon any shelf or desk,this fun and historic cruise ship model will add a touch of nautical history and maritime luxury to the décor of any room.14″Long x 2.5″Wide x 6.5″High (1:757 scale) Built from… |
